Onsrud Series 10-00

1 Flute - High Speed Steel O Flute Straight Router Bits
Usage: ABS, polycarbonate, polyethylene, PVC, polypropylene, polystyrene, extruded acrylic, HDPE, UHMW, and natural wood
(SW) = Soft Wood
(SP) = Soft Plastic
Onsrud Series 11-00 - 2 Flutes

2 Flute High Speed Steel O Flute Straight
Usage: ABS, polycarbonate, polyethylene, polystyrene, PVC, polypropylene, extruded acrylic, HDPE, UHMW
(HP) = Hard Plastic
(SP) = Soft Plastic
Onsrud Series 11-00 - 1 Flutes

1 Flute - High Speed Steel O Flute Straight Router Bits
Usage: ABS, polycarbonate, polyethylene, polystyrene, PVC, polypropylene, extruded acrylic, HDPE, UHMW
(HP) = Hard Plastic
(SP) = Soft Plastic
Onsrud Series 12-00

2 Flute - High Speed Steel Straight Router Bits V Flute
Usage: Foam and natural wood
(HW) = Hard Wood
(FP) = Foam
Onsrud Series 15-40

1 Flute - High Speed Steel Compression-Spiral Dor Bits
Usage: Metal Clad Doors, Fiberglass Doors
(D) = Metal Doors
Onsrud Series 15-50

1 Flute - High Speed Steel Dor-Bits
Usage: Metal Clad Doors, Fiberglass Doors
(D) = Metal Doors
Onsrud Series 18-00

1 Flute - High Speed Steel Single Edge Straight Pilot
Usage: Wood panels, vinyl coated panels, wall board, and aluminum layered materials
(CM/DW) = Construction Material
Onsrud Series 20-00

1 Flute – High Speed Steel Downcut Spiral Pilot Bits
Usage: Aluminum and plywood sandwich panels vinyl coated panels, wall bored, drywall and layered material
(CM/DW) = Construction Material
Onsrud Series 20-10

1 Flute - High Speed Steel Drywall Bit
Usage: Drywall cut outs
(CM/DW) = Construction Material
Onsrud Series 27-00

1 Flute - Solid Carbide Single Edge Laminate Trim
Usage: Trimming laminate counter tops and trimming plastic parts
(LW) = Laminated and Veneered
Onsrud Series 27-50

2 Flute - Solid Carbide Single Edge Laminate Trim
Usage: Trimming laminate counter tops and trimming plastic parts
(LW) = Laminated and Veneered
Onsrud Series 28-20

2 Flute - Solid Carbide Double Bearing Plastic Trim
Usage: Trimming stacked sheets plastic and laminates
(SP) = SoftPlastic
(HP) = HardPlastic
Onsrud Series 28-50

2 Flute - Carbide Tipped Flush Trim
Usage: Natural wood, wood composites
(LW) = Laminated and Veneered
(SW) = Softwood
(HW) = Hardwood
(CW) = Composite Wood
Onsrud Series 29-000

High Speed Steel Hollow Core for Honeycomb
Usage: Honeycomb
(HC) = Honeycomb
Onsrud Series 29-050 - Hogger

Diamond Grit Honeycomb Hogger
Usage: Honeycomb, Graphite, Phenolic or Fiberglass
(HC) = Honeycomb
Onsrud Series 29-050 - Ball Nose Hogger

Diamond Grit Ball Nose Honeycomb Hogger
Usage: Honeycomb, Graphite, Phenolic or Fiberglass
(HC) = Honeycomb
Onsrud Series 29-050 - Metric Ball Nose Hogger

Diamond Grit Metric Ball Nose Honeycomb Hogger
Usage: Honeycomb, Graphite, Phenolic or Fiberglass
(HC) = Honeycomb
Onsrud Series 29-100

Multi-Flulte - Solid Carbide Honeycomb Hogger - ZRN Coated
Usage: Honeycomb
(HC) = Honeycomb
Onsrud Series 29-100 - Ball Nose

Multi-Flulte - Solid Carbide Ballnose Honeycomb Hogger - ZRN Coated
Usage: Honeycomb
(HC) = Honeycomb
Onsrud Series 29-50

2 Flute - Carbide Tipped Chamfer
Usage: Natural wood and wood composites
(SW) = Softwood
(HW) = Hardwood
(CW) = Composite Wood
Onsrud Series 30-000 - Shank Assembly

HSS - Replaceable Ring Honeycomb Cutter Shank Assembly
Usage: Honeycomb; for contouring, carving and chamfering cuts
(HC) = Honeycomb
Onsrud Series 30-000 - Cutting Blades

Cutting Blade for Honeycomb Assemblies
Usage: Honeycomb; for contouring, carving and chamfering cuts
(HC) = Honeycomb
Onsrud Series 30-300 - Hogger

Multi-Flute – High Speed Steel Integral Shank Honeycomb Hogger
Usage: Honeycomb
(HC) = Honeycomb
Onsrud Series 30-300 - Cutting Blade

Cutting Blade for Honeycomb Assemblies
Usage: Honeycomb; CNC Machining of Honeycomb Core
(HC) = Honeycomb
Onsrud Series 30-700 - Hogger

Multi-Flute – HSS Reduced Weight Honeycomb Cutter
Usage: Honeycomb
(HC) = Honeycomb
Onsrud Series 31-000

High Speed Steel Honeycomb Cutter
Usage: Aluminum Core
(HC) = Honeycomb
Onsrud Series 31-100

High Speed Steel Honeycomb Cutter with Teeth, TICN Coated
Usage: Aluminum Core
(HC) = Honeycomb
Onsrud Series 32-000 - Shank Assembly

Honeycomb Hogger Arbor
Usage: Honeycomb
(HC) = Honeycomb
Onsrud Series 32-000 - Hogger

Honeycomb Hogger
Usage: Honeycomb
(HC) = Honeycomb
Onsrud Series 32-000 - Cutting Blade

Honeycomb Cutting Blade
Usage: Honeycomb
(HC) = Honeycomb
Onsrud Series 32-200 - Shank Assembly

Arbor for Honeycomb; requires Hogger and Blade
Usage: Honeycomb
(HC) = Honeycomb
Onsrud Series 32-200 - Hogger

Hogger for Honeycomb; requires Arbor and Blade
Usage: Honeycomb
(HC) = Honeycomb
Onsrud Series 34-000

Diamond Grit Aircraft Panel Tools
Usage: Honeycomb
(HC) = Honeycomb
Onsrud Series 34-100 - Metric

Solid Carbide Metric Potted Fastener Tool; ZRN Coated
Usage: Honeycomb
(HC) = Honeycomb
Onsrud Series 34-100

Solid Carbide Potted Fastener Tool; ZRN Coated
Usage: Honeycomb
(HC) = Honeycomb
Onsrud Series 37-00

1 Flute - Solid Carbide 60° Engraving Bit
Usage: Wood, plastic, aluminum, and solid surface
(SW) = Softwood
(HW) = Hardwood
(SP) = Soft Plastic
(HP) = Hard Plastic
(A) = Aluminum
(SSP) = Solid Surface
Onsrud Series 37-00 - Metric

1 Flute - Solid Carbide 60° Metric Engraving Bit
Usage: Wood, plastic, aluminum, and solid surface
(SW) = Softwood
(HW) = Hardwood
(SP) = Soft Plastic
(HP) = Hard Plastic
(A) = Aluminum
(SSP) = Solid Surface
Onsrud Series 37-20

1 Flute - Solid Carbide 30° Engraving Bit
Usage: Wood, plastic, aluminum, and solid surface
(SW) = Softwood
(HW) = Hardwood
(SP) = Soft Plastic
(HP) = Hard Plastic
(A) = Aluminum
(SSP) = Solid Surface
Onsrud Series 37-20 - Metric

1 Flute - Solid Carbide 30° Metric Engraving Bit
Usage: Wood, plastic, aluminum, and solid surface
(SW) = Softwood
(HW) = Hardwood
(SP) = Soft Plastic
(HP) = Hard Plastic
(A) = Aluminum
(SSP) = Solid Surface
Onsrud Series 37-50

2 Flute - Solid Carbide V Bottom
Usage:
(SW) = Softwood
(HW) = Hardwood
(CW) = Composite Wood
(SP) = Soft Plastic
(HP) = Hard Plastic
(SSP) = Solid Surface
(LW) = Laminated and Veneer
Onsrud Series 37-60

2 Flute - Carbide Tipped V Bottom
Usage:
(SW) = Softwood
(HW) = Hardwood
(CW) = Composite Wood
(SP) = Soft Plastic
(HP) = Hard Plastic
(SSP) = Solid Surface
(LW) = Laminated and Veneer
Onsrud Series 37-70

2 Flute - Carbide Tipped Folding Tool
Usage:
(A) = Aluminum
Onsrud Series 37-80

2 Flute – Carbide Tipped Lettering Bits
Usage: Wood
(SW) = Softwood
(HW) = Hardwood
(CW) = Composite Wood
Onsrud Series 40-000 - Upcut

1 Flute – High Speed Steel Upcut Spiral
Usage: Natural wood, Sheet and stacked aluminum
(SW) = Softwood
(HW) = Hardwood
(A) = Aluminum
Onsrud Series 40-000 - Downcut

1 Flute – High Speed Steel Downcut Spiral
Usage: Natural wood, Sheet and stacked aluminum
(SW) = Softwood
(HW) = Hardwood
(A) = Aluminum
Onsrud Series 40-100 - Upcut

2 Flute – High Speed Steel Upcut Spiral
Usage: Natural wood, Sheet block and plate aluminum
(SW) = Softwood
(HW) = Hardwood
(A) = Aluminum
Onsrud Series 40-100 - Downcut

2 Flute – High Speed Steel Downcut Spiral
Usage: Natural wood, Sheet block and plate aluminum
(SW) = Softwood
(HW) = Hardwood
(A) = Aluminum
Onsrud Series 40-50

2 Flute - Carbide Tipped Round & Rout
Usage:
(SW) = Softwood
(HW) = Hardwood
(CW) = Composite Wood
(SP) = Soft Plastic
(HP) = Hard Plastic
(SSP) = Solid Surface
Onsrud Series 40-550

4 Flute – High Speed Steel Upcut Spiral Foam Cutters
Usage: Foam Boards
(FP) = Foam
Onsrud Series 42-00

2 Flute - Carbide Tipped Corner Round
Usage: Natural wood, wood composites, and solid surface
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Woods
(SSP) = Solid Surface
Onsrud Series 47-00

Carbide Tipped MDF Panel Tools
Usage: MDF
(CW) = Composite Woods
Onsrud Series 48-000 - 2 Flutes

2 Flute – Carbide Tipped Straight
Usage: Hard Wood, Soft Wood, Wood Composite, Foam
(HW) = Hard Wood
(CW) = Composite Wood
(LW) = Laminated Wood
(FP) = Foam
Onsrud Series 48-000 - 1 Flute

1 Flute – Carbide Tipped Straight
Usage: Hard Wood, Soft Wood, Wood Composite, Foam
(HW) = Hard Wood
(CW) = Composite Wood
(LW) = Laminated Wood
(FP) = Foam
Onsrud Series 49-000

2 Flute - High Speed Steel Downcut-Spiral Router Bits for Aluminum
Usage: Aluminum and non-abrasive plastics
(A) = Aluminum
Onsrud Series 52-000

2 Flute – Solid Carbide Upcut Spiral Router Bits
Usage: Fiberglass, Solid Surface, Aluminum Slab
(A) = Aluminum
(SSP) = Solid Surface
Onsrud Series 52-200 - Ball Nose

2 Flute – Solid Carbide Ball Nose Upcut Spiral
Usage:Soft Wood, Hard Wood, Wood Composite, Soft Plastic, Hard Plastic, Aluminum
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
(SP) = Soft Plastic
(HP) = Hard Plastic
(A) = Aluminum
(SSP) = Solid Surface
Onsrud Series 52-200 - Ball Nose Extd Length

2 Flute – Solid Carbide Ball Nose Extended Length Upcut Spiral
Usage:Soft Wood, Hard Wood, Wood Composite, Soft Plastic, Hard Plastic, Aluminum
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
(SP) = Soft Plastic
(HP) = Hard Plastic
(A) = Aluminum
(SSP) = Solid Surface
Onsrud Series 52-200

2 Flute – Solid Carbide Wood Rout Upcut Spiral
Usage: Soft Wood, Hard Wood, Wood Composite
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
(SP) = Soft Plastic
Onsrud Series 52-200 - Ball Nose Metric

2 Flute – Solid Carbide Metric Ball Nose Upcut Spiral
Usage:Soft Wood, Hard Wood, Wood Composite, Soft Plastic, Hard Plastic, Aluminum
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
(SP) = Soft Plastic
(HP) = Hard Plastic
(A) = Aluminum
(SSP) = Solid Surface
Onsrud Series 52-400

2 Flute – Solid Carbide Wood Rout Upcut Spiral
Usage: Soft Wood, Hard Wood, Wood Composite
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
(SP) = Soft Plastic
Onsrud Series 52-550

2 Flute – Solid Carbide Upcut Foam Cutters
Usage: Foam
(FP) = Foam Products
Onsrud Series 56-200

2 Flute - Solid Carbide O Flute Upcut-Spiral Router Bits
Usage: Soft Plastic, Solid Surface, Foam, Soft Wood, Hard Wood
(SP) = Soft Plastics
(SSP) = Solid Surface
(FP) = Foam
(SW) = Soft Wood
(HW) = Hard Wood
Onsrud Series 52-700

2 Flute - Solid Carbide Metric O Flute Upcut-Spiral Router Bits
Usage: Soft Plastic, Solid Surface, Foam, Soft Wood, Hard Wood
(SP) = Soft Plastics
(SSP) = Solid Surface
(FP) = Foam
(SW) = Soft Wood
(HW) = Hard Wood
Onsrud Series 52-700 - Metric

2 Flute – Solid Carbide Extreme Heavy Duty Upcut Spiral
Usage: Soft Wood, Hard Wood, Wood Composite
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
Onsrud Series 52-900

3 Flute - Solid Carbide Straight Router Bits
Usage: Composites
(CP) = Composite Plastics
Onsrud Series 53-000

3 and 4 Flute - Solid Carbide Upcut Spiral for Glass Reinforced Plastic; Fet1 Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 54-200 - Upcut

3 and 4 Flute - Solid Carbide Downcut Spiral for Glass Reinforced Plastic; Fet1 Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 54-200 - Downcut

3 and 4 Flute - Solid Carbide Metric Upcut Spiral for Glass Reinforced Plastic; Fet1 Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 54-200 - Upcut Metric

3 and 4 Flute - Solid Carbide Metric Downcut Spiral for Glass Reinforced Plastic; Fet1 Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 54-200 - Downcut Metric

2 Flute – Solid Carbide Straight V Flute Router Bit
Usage: Composite Plastic
(HP) = Hard Plastic
(CP) = Composite
Onsrud Series 56-000

2 Flute – Solid Carbide Straight V Flute Router Bit
Usage: Hard Plastic, Composite Plastic, Solid Surface, Foam
(HP) = Hard Plastic
(CP) = Composites
(SSP) = Solid Surface
(FP) = Foam
Onsrud Series 56-000P

2 Flute – Solid Carbide Straight V Flute Router Bit
Usage: Natural wood and wood composites
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
Onsrud Series 56-430

2 Flute – Solid Carbide Straight O Flute Router Bit
Usage: Soft Plastic, Hard Plastic
(HP) = Hard Plastic
(SP) = Soft Plastic
Onsrud Series 56-450

2 Flute – Solid Carbide Straight V Flute Router Bit
Usage: Hard Plastic, Composite Plastic, Solid Surface
(HP) = Hard Plastic
(CP) = Composite
(SSP) = Solid Surface
Onsrud Series 56-600

2 Flute - Solid Carbide Straight O Flute Router Bits
Usage: Soft Plastic, Hard Plastic
(HP) = Hard Plastic
(SP) = Soft Plastic
Onsrud Series 57-000

2 Flute – Solid Carbide Downcut Spiral
Usage: Aluminum, Composite Plastic
(CP) = Composites
(A) = Aluminum
(SSP) = Solid Surface
Onsrud Series 57-200

2 Flute – Solid Carbide Downcut Spiral Wood Rout
Usage: Soft Wood, Hard Wood, Wood Composites
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
Onsrud Series 57-200MD


Usage: Soft Wood, Hard Wood, Wood Composite
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
(LW) = Laminated Wood
Onsrud Series 57-400

2 Flute – Solid Carbide Downcut Spiral Wood Rout
Usage: Soft Wood, Hard Wood, Wood Composites
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
Onsrud Series 57-600

2 Flute – Solid Carbide O Flute Downcut Spiral
Usage: Acrylic, Nylon, ABS, PE, Acetal, PET, HDPE, UHMW, Polycarbonate, and Solid Surface
(SP) = Soft Plastic
(HP) = Hard Plastic
(SSP) = Solid Surface
Onsrud Series 57-600 - Metric

2 Flute – Solid Carbide Metric O Flute Downcut Spiral
Usage: Acrylic, Nylon, ABS, PE, Acetal, PET, HDPE, UHMW, Polycarbonate, and Solid Surface
(SP) = Soft Plastic
(HP) = Hard Plastic
(SSP) = Solid Surface
Onsrud Series 57-900

2 Flute – Solid Carbide Downcut Extreme Heavy Duty
Usage: Soft Wood, Hard Wood, Wood Composites
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
Onsrud Series 60-000 - High Helix Upcut

3 Flute – Solid Carbide High Helix Hogger Upcut Spiral
Usage: Soft Wood, Hard Wood, Wood Composites, Hard Plastic, Soft Plastic
(SW) = Soft Wood
(HW) = Hard Wood
(SP) = Soft Plastic
(CW) = Composite Wood
(HP) = Hard Plastic
Onsrud Series 60-000 - High Helix Downcut

3 Flute – Solid Carbide High Helix Hogger Downcut Spiral
Usage: Soft Wood, Hard Wood, Wood Composites, Hard Plastic, Soft Plastic
(SW) = Soft Wood
(HW) = Hard Wood
(SP) = Soft Plastic
(CW) = Composite Wood
(HP) = Hard Plastic
Onsrud Series 60-000 - Low Helix Upcut

3 Flute – Solid Carbide Low Helix Hogger Upcut Spiral
Usage: Soft Wood, Hard Wood, Wood Composites, Hard Plastic, Soft Plastic
(SW) = Soft Wood
(HW) = Hard Wood
(SP) = Soft Plastic
(CW) = Composite Wood
(HP) = Hard Plastic
Onsrud Series 60-000 - Low Helix Downcut

3 Flute – Solid Carbide Low Helix Hogger Downcut Spiral
Usage: Soft Wood, Hard Wood, Wood Composites, Hard Plastic, Soft Plastic
(SW) = Soft Wood
(HW) = Hard Wood
(SP) = Soft Plastic
(CW) = Composite Wood
(HP) = Hard Plastic
Onsrud Series 60-090

3 Flute - Solid Carbide Lock Mortise Upcut-Spiral
Usage: Natural wood and Wood composites
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
Onsrud Series 60-100MW - Single Flute

1 Flute – Solid Carbide Max Life Compression Spiral
Usage: Double sided laminated and veneered materials
(CW) = Composite Wood
(HW) = Hard Wood
(SW) = Soft Wood
(LW) = Laminated Wood
Onsrud Series 60-100MW - Double Flute

2 Flute – Solid Carbide Max Life Compression Spiral
Usage: Double sided laminated and veneered materials
(CW) = Composite Wood
(HW) = Hard Wood
(SW) = Soft Wood
(LW) = Laminated Wood
Onsrud Series 60-100C

2 Flute – Solid Carbide Chipbreaker Finisher Compression Spiral
Usage: Double sided laminated and veneered materials
(CW) = Composite Wood
(HW) = Hard Wood
(SW) = Soft Wood
(LW) = Laminated Wood
Onsrud Series 60-100DC

2 Flute – Solid Carbide Dual Core Compression Spiral
Usage: Double sided laminated and veneered materials
(CW) = Composite Wood
(HW) = Hard Wood
(SW) = Soft Wood
(LW) = Laminated Wood
Onsrud Series 60-100MC - Double Flute

2 Flute – Solid Carbide Marathon Compression Spiral; Marathon Coated
Usage: Double sided laminated and veneered materials
(CW) = Composite Wood
(HW) = Hard Wood
(SW) = Soft Wood
(LW) = Laminated Wood
Onsrud Series 60-100PLR - Double Flute

2 Flute – Solid Carbide Polaris Compression Spiral; Polaris Coated
Usage: Double sided laminated and veneered materials
(CW) = Composite Wood
(HW) = Hard Wood
(SW) = Soft Wood
(LW) = Laminated Wood
Onsrud Series 60-100MW - Three Flute

3 Flute – Solid Carbide Max Life Compression Spiral
Usage: Double sided laminated and veneered materials
(CW) = Composite Wood
(HW) = Hard Wood
(SW) = Soft Wood
(LW) = Laminated Wood
Onsrud Series 60-100MC - Triple Flute

3 Flute – Solid Carbide Marathon Compression Spiral; Marathon Coated
Usage: Double sided laminated and veneered materials
(CW) = Composite Wood
(HW) = Hard Wood
(SW) = Soft Wood
(LW) = Laminated Wood
Onsrud Series 60-100MC - Metric

1 and 2 Flute – Solid Carbide Metric Marathon Compression Spiral; Marathon Coated
Usage: Double sided laminated and veneered materials
(CW) = Composite Wood
(HW) = Hard Wood
(SW) = Soft Wood
(LW) = Laminated Wood
Onsrud Series 60-100MW - Metric

1 Flute – Solid Carbide Max Life Compression Spiral
Usage: Double sided laminated and veneered materials
(CW) = Composite Wood
(HW) = Hard Wood
(SW) = Soft Wood
(LW) = Laminated Wood
Onsrud Series 60-200 - Upcut

3 Flute – Solid Carbide Low Helix Finisher Upcut Spiral
Usage: Soft Wood, Hard Wood, Plastic, Solid Surface
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
(HP) = Hard Plastic
(SSP) = Solid Surface
Onsrud Series 60-200 - Downcut

3 Flute – Solid Carbide Low Helix Finisher Downcut Spiral
Usage: Soft Wood, Hard Wood, Plastic, Solid Surface
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
(HP) = Hard Plastic
(SSP) = Solid Surface
Onsrud Series 60-300 - Upcut


Usage: Natural wood and wood composites
(HW) = Hard Wood
(CW) = Composite Wood
(SW) = Soft Wood
Onsrud Series 60-300 - Downcut


Usage: Natural wood and wood composites
(HW) = Hard Wood
(CW) = Composite Wood
(SW) = Soft Wood
Onsrud Series 60-350 - Upcut

3 Flute - Solid Carbide Chipbreaker/Finisher Upcut Spiral
Usage: Natural wood and wood composites
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
Onsrud Series 60-350 - Downcut

3 Flute - Solid Carbide Chipbreaker/Finisher Downcut Spiral
Usage: Natural wood and wood composites
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
Onsrud Series 60-200 - Metric Upcut

3 Flute – Solid Carbide Low Helix Finisher Metric Upcut Spiral
Usage: Soft Wood, Hard Wood, Plastic, Solid Surface
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
(HP) = Hard Plastic
(SSP) = Solid Surface
Onsrud Series 60-500

4 Flute - Solid Carbide Compression Spiral
Usage: Double-Sided Laminated and Veneered Wood Composites
(LW) = Laminated Wood
(CW) = Composite Wood
Onsrud Series 60-600

4 Flute – Solid Carbide High Velocity Compression Spiral
Usage: High velocity routing of double sided laminated and veneered, natural wood and wood composites.
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
(LW) = Laminated Wood
Onsrud Series 60-700 - Downcut

4 Flute – Solid Carbide High Velocity Downcut Spiral
Usage: High velocity routing of Double-Sided Laminated and Veneered Wood Composites, Soft Wood, Hard Wood
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
Onsrud Series 60-700 - Upcut

4 Flute – Solid Carbide High Velocity Upcut Spiral
Usage: High velocity routing of Double-Sided Laminated and Veneered Wood Composites, Soft Wood, Hard Wood
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
Onsrud Series 60-800 - Upcut

2 Flute – Solid Carbide Rougher Upcut Spiral
Usage: Soft Wood, Hard Wood, Wood Composites
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
Onsrud Series 60-800 - Downcut

2 Flute – Solid Carbide Rougher Downcut Spiral
Usage: Soft Wood, Hard Wood, Wood Composites
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
Onsrud Series 60-900 - Upcut

3 Flute – Solid Carbide Extreme Heavy Duty Hogger Upcut Spiral
Usage: Natural wood and wood composites
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
(SP) = Soft Plastic
(HP) = Hard Plastic
Onsrud Series 60-900 - Downcut

3 Flute – Solid Carbide Extreme Heavy Duty Hogger Downcut Spiral
Usage: Natural wood and wood composites
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
(SP) = Soft Plastic
(HP) = Hard Plastic
Onsrud Series 60-950 - Downcut

2 Flute – Solid Carbide Extreme Heavy Duty Chipbreaker/Finisher Downcut Spiral
Usage: Natural wood and wood composites
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
Onsrud Series 60-950 - Upcut

2 Flute – Solid Carbide Extreme Heavy Duty Chipbreaker/Finisher Upcut Spiral
Usage: Natural wood and wood composites
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
Onsrud Series 61-000

1 Flute - Solid Carbide Straight Router Bits
Usage: Soft Wood, Aluminum Sheet
(SW) = Soft Wood
(A) = Aluminum
Onsrud Series 61-000P

1 Flute – Solid Carbide O Flute Straight Router Bit
Usage: Soft Plastic, Hard Plastic
(SP) = Soft Plastic
(HP) = Hard Plastic
Onsrud Series 61-200

1 Flute – Solid Carbide V Flute Straight Wood Rout
Usage: Natural wood and wood composites
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Wood Composites
Onsrud Series 61-400

1 Flute – Solid Carbide O Flute Straight Router Bit
Usage: Polycarbonate, Polyethylene, Polypropylene, Polystyrene, PVC, Extruded Acrylic, HDPE, UHMW, and hard plastic
(SP) = Soft Plastic
(HP) = Hard Plastic
Onsrud Series 62-600

1 Flute - Solid Carbide O Flute Downcut-Spiral Router Bits
Usage: Aluminum, Plate, Single and Multi-Sheet
(A) = Aluminum
Onsrud Series 62-700

1 Flute - Solid Carbide O Flute Downcut-Spiral for Hard Plastics
Usage: Hard Plastic, Solid Surface
(HP) = Hard Plastic
(SSP) = Solid Surface
Onsrud Series 62-750

1 Flute - Solid Carbide O Flute Downcut-Spiral for Soft Plastics
Usage: Soft Plastic, Solid Surface
(SP) = Soft Plastic
(SSP) = Solid Surface
Onsrud Series 62-800

1 Flute - Solid Carbide O Flute Downcut-Spiral for Hard Plastics
Usage: Hard Plastic, Solid Surface
(HP) = Hard Plastic
(SSP) = Solid Surface
Onsrud Series 62-850

1 Flute - Solid Carbide O Flute Downcut-Spiral for Soft Plastics
Usage: Soft Plastic, Solid Surface
(SP) = Soft Plastic
(SSP) = Solid Surface
Onsrud Series 63-000

1 Flute - Solid Carbide Upcut-Spiral Router Bits
Usage: Fiberglass, Aluminum Sheet
(A) = Aluminum
(CP) = Composites
Onsrud Series 63-200

1 Flute – Solid Carbide Upcut Spiral Wood Rout
Usage: Natural wood and wood composites
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
Onsrud Series 63-400

1 Flute - Solid Carbide Upcut-Spiral for Soft Aluminum; ZRN Coated
Usage: Soft Aluminum Sheet
(A) = Aluminum
Onsrud Series 63-500

1 Flute – Solid Carbide O Flute Upcut Spiral for Acrylics
Usage: Acrylics
(SP) = Soft Plastic
(HP) = Hard Plastic
Onsrud Series 63-600

1 Flute - Solid Carbide O Flute Upcut-Spiral for Aluminum
Usage: Aluminum plate and single/multi sheet
(A) = Aluminum
Onsrud Series 63-700

1 Flute - Solid Carbide O Flute Upcut-Spiral for Hard Plastics
Usage: Hard Plastic, Solid Surface
(HP) = Hard Plastic
(SSP) = Solid Surface
Onsrud Series 63-750

1 Flute - Solid Carbide O Flute Upcut-Spiral for Soft Plastics
Usage: Soft Plastic, Solid Surface
(SP) = Soft Plastic
(SSP) = Solid Surface
Onsrud Series 63-800

1 Flute - Solid Carbide O Flute Upcut-Spiral for Hard Plastics
Usage: Hard Plastic, Solid Surface
(HP) = Hard Plastic
(SSP) = Solid Surface
Onsrud Series 63-850

1 Flute - Solid Carbide O Flute Upcut-Spiral for Soft Plastics
Usage: Soft Plastic, Solid Surface
(SP) = Soft Plastic
(SSP) = Solid Surface
Onsrud Series 63-900

1 Flute – Solid Carbide O Flute Upcut Spiral for Aluminum
Usage: Aluminum plate and single/multi sheet
(A) = Aluminum
Onsrud Series 64-000

1 Flute – Solid Carbide O Flute Downcut Spiral Router Bits
Usage: Plastic, Wood, Aluminum, Solid Surface
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
(SP) = Soft Plastic
(HP) = Hard Plastic
(SSP) = Solid Surface
(A) = Aluminum
Onsrud Series 65-000

1 Flute – Solid Carbide Upcut Spiral Super O Flute
Usage: Plastic, Wood, Aluminum, Solid Surface
(SW) = Soft Wood
(HW) = Hard Wood
(CW) = Composite Wood
(SP) = Soft Plastic
(HP) = Hard Plastic
(SSP) = Solid Surface
(A) = Aluminum
Onsrud Series 65-200B

2 Flute - Solid Carbide High Finish Ballnose Upcut Spiral for Plastic
Usage: Soft Plastic
(SP) = Soft Plastic
Onsrud Series 65-300B

4 Flute - Solid Carbide High Finish Ballnose Upcut Spiral for Plastic
Usage: Soft Plastic
(SP) = Soft Plastic
Onsrud Series 66-000 Single Flute Straight O Flute

1 Flute – Solide Carbide Straight O Flute Edge Rounding
Usage: Edge rounding of parts
(SSP) = Solid Surface
(HP) = Hard Plastic
(SP) = Soft Plastic
Onsrud Series 66-000 Single Flute Spiral O Flute

1 Flute – Solide Carbide Spiral O Flute Edge Rounding
Usage: Edge rounding of parts
(SSP) = Solid Surface
(HP) = Hard Plastic
(SP) = Soft Plastic
Onsrud Series 66-000 Double Flute Straight O Flute

2 Flute – Solide Carbide Straight O Flute Edge Rounding
Usage: Edge rounding of parts
(SSP) = Solid Surface
(HP) = Hard Plastic
(SP) = Soft Plastic
Onsrud Series 66-000 Double Flute Straight V Flute

2 Flute – Solid Carbide Straight V Flute Edge Rounding
Usage: Edge rounding of parts
(SSP) = Solid Surface
(HP) = Hard Plastic
(SP) = Soft Plastic
Onsrud Series 66-200

2 Flute - Solid Carbide Straight V Flute Rout & Chamfer
Usage: Soft Plastic, Hard Plastic
(SP) = Soft Plastic
(HP) = Hard Plastic
Onsrud Series 66-300

2 Flute - Solid Carbide Bottom Surfacing Upcut-Spiral
Usage: Soft Plastic, Hard Plastic, Aluminum
(SP) = Soft Plastic
(HP) = Hard Plastic
(A) = Aluminum
Onsrud Series 66-400

6 Flute - Solid Carbide Compression; ZRN Coated
Usage: Honeycomb Panel, Cardboard Honeycomb
(HC) = Honeycomb
Onsrud Series 66-500

Multi Flutes - Solid Carbide Composite Chisel Tooth Router; DFC Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 66-500 - Metric

Multi Flutes - Solid Carbide Metric Composite Chisel Tooth Router; DFC Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 66-700

Multi Flutes - Solid Carbide Low-Helix Finisher Composite Upcut Spiral; DFC Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 66-750 - Upcut

Multi Flutes - Solid Carbide Low-Helix Composite Cutter Upcut Spiral; DFC Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 66-750 - Metric Upcut

Multi Flutes - Solid Carbide Low-Helix Composite Cutter Metric Upcut Spiral; DFC Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 66-750 - Downcut

Multi Flutes - Solid Carbide Low-Helix Composite Cutter Downcut Spiral; DFC Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 66-750 - Metric Downcut

Multi Flutes - Solid Carbide Low-Helix Composite Cutter Metric Downcut Spiral; DFC Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 66-775

Multi Flutes - Solid Carbide Low-Helix Rougher Finisher Composite Upcut Spiral; DFC Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 66-800

Multi Flutes - Solid Carbide Composite Compression; DFC Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 66-900

Multi Flute - Solid Carbide High Performance Composite Router; ESG Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 66-900 - Burr Point

Multi Flute - Solid Carbide High Performance Composite Router with Burr Point; ESG Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 66-900 - End Mill Point

Multi Flute - Solid Carbide High Performance Composite Router with End Mill Point; ESG Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 66-900 - Drill Point

Multi Flute - Solid Carbide High Performance Composite Router with Drill Point; ESG Coated
Usage: Composite, Fiberglass
(CP) = Composite
Onsrud Series 67-000 - Med Burr End Mill Point

Multi-Flute - Solid Carbide Fiberglass Medium Burr End Mill Point
Usage: Fiberglass and Composites
(CP) = Composites
Onsrud Series 67-000 - Metric Med Burr End Mill Point

Multi-Flute - Solid Carbide Fiberglass Metric Medium Burr End Mill Point
Usage: Fiberglass and Composites
(CP) = Composites
Onsrud Series 67-000 - Fine Burr Drill Point

Multi-Flute - Solid Carbide Fiberglass Fine Burr Drill Point
Usage: Fiberglass and Composites
(CP) = Composites
Onsrud Series 67-000 - Metric Fine Burr Drill Point

Multi-Flute - Solid Carbide Fiberglass Metric Fine Burr Drill Point
Usage: Fiberglass and Composites
(CP) = Composites
Onsrud Series 67-200 - Upcut

3 Flute – Solid Carbide Phenolic Chipbreaker Upcut
Usage: Phenolic
(CP) = Composite
Onsrud Series 67-200 - Downcut

3 Flute – Solid Carbide Phenolic Chipbreaker Downcut
Usage: Phenolic
(CP) = Composite
Onsrud Series 67-250

3 Flute - Solid Carbide Diamond Grit Composite Tool Downcut Spiral
Usage: Fiberglass and Composites
(CP) = Composite
Onsrud Series 67-400

2 Flute - Solid Carbide Un-Ruffer for Composites
Usage: Composite panels
(CP) = Composites
Onsrud Series 67-500

Multi Flute - Solid Carbide Carbon Graphite Router
Usage: Carbon Graphite, Carbon Fiber Panels
(CP) = Composites
Onsrud Series 67-800 - Fractional Drills

2 Flute - Solid Carbide 8 Facet Drills - Fractional Drills
Usage: Carbon fiber and other Composite material
(CP) = Composites
Onsrud Series 67-800 - Letter Drills

2 Flute - Solid Carbide 8 Facet Drills - Letter Drills
Usage: Carbon fiber and other Composite material
(CP) = Composites
Onsrud Series 67-800 - Number Drills

2 Flute - Solid Carbide 8 Facet Drills - Number Drills
Usage: Carbon fiber and other Composite material
(CP) = Composites
Onsrud Series 67-800 - Metric Drills

2 Flute - Solid Carbide 8 Facet Drills - Metric Drills
Usage: Carbon fiber and other Composite material
(CP) = Composites
Onsrud Series 68-000

2 Flute - PCD Tipped Router
Usage: Composite panels and Fiberglass
(CP) = Composite Plastic
Onsrud Series 68-000 - Plunge Point

2 Flute - PCD Tipped Router with Plunge Point
Usage: Composite panels and Fiberglass
(CP) = Composite Plastic
Onsrud Series 68-100

1 Flute - PCD Tipped Compression Router Bits
Usage: Double-Sided Laminated and Veneered Wood Composites
(CW) = Composite Wood
(SW) = Soft Wood
(HW) = Hard Wood
(LW) = Laminated Wood
Onsrud Series 68-200

2 Flute – PCD SERF Cutter
Usage: Composite, Fiberglass
(CP) = Composites
Onsrud Series 68-300

3 Flute – PCD SERFIN Cutter
Usage: Composite, Fiberglass
(CP) = Composites
Onsrud Series 68-900

2 Flute - PCD 8 Facet Drills
Usage: Composite
(CP) = Composites
Onsrud Series 70-100 - Soft Plastic - Slow Feed

Carbide Tipped Trim Blade and Arbor for Soft Plastic, Slow Feed
Usage: Soft Plastics
(SP) = Soft Plastic
Onsrud Series 70-100 - Soft Plastic - Fast Feed

Carbide Tipped Trim Blade and Arbor for Soft Plastic, Fast Feed
Usage: Soft Plastics
(SP) = Soft Plastic
Onsrud Series 70-100 - Hard Plastic - Fast Feed

Carbide Tipped Trim Blade and Arbor for Hard Plastic, Fast Feed
Usage: Hard Plastics
(HP) = Hard Plastics
Onsrud Series 70-100 - Arbor

Arbor for Carbide Tipped Trim Saws
Usage: Hard and Soft Plastics
(HP) = Hard Plastics
(SP) = Soft Plastics
Onsrud Series 70-200

Solid Carbide Trim Blade Flush Mount
Usage: Hard and Soft Plastics
(HP) = Hard Plastics
(SP) = Soft Plastics
Onsrud Series 70-300 - Soft Plastic

Carbide Tipped Trim Blade Flush Mount for Soft Plastics
Usage: Soft Plastics
(SP) = Soft Plastics
Onsrud Series 70-300 - Hard Plastic

Carbide Tipped Trim Blade Flush Mount for Hard Plastics
Usage: Hard Plastics
(HP) = Hard Plastics
Onsrud Series 70-500 - Fractional Drills

2 Flute - HSS Plastic Drill; Fractional Drills
Usage: Hard and Soft Plastics
(HP) = Hard Plastics
(SP) = Soft Plastics
Onsrud Series 70-500 - Metric Drills

2 Flute - HSS Plastic Drill; Metric Drills
Usage: Hard and Soft Plastics
(HP) = Hard Plastics
(SP) = Soft Plastics
Onsrud Series 72-000 - Brad Point

2 Flute - Solid Carbide Boring Bits, Brad Point
Usage: Soft Wood, Hard Wood, Wood Composite, Laminated Wood
(HW) = Hard Wood
(SW) = Soft Wood
(CW) = Composite Wood
(LW) = Laminated Wood
Onsrud Series 72-000 - Through Hole

2 Flute - Solid Carbide Boring Bits, Through Hole
Usage: Soft Wood, Hard Wood, Wood Composite, Laminated Wood
(HW) = Hard Wood
(SW) = Soft Wood
(CW) = Composite Wood
(LW) = Laminated Wood
Onsrud Series 72-000 - Hinge Bit

2 Flute - Carbide Tipped Boring Bits, Hinge Bit
Usage: Soft Wood, Hard Wood, Wood Composite, Laminated Wood
(HW) = Hard Wood
(SW) = Soft Wood
(CW) = Composite Wood
(LW) = Laminated Wood
Onsrud Series 77-100

2 Flute and 3 Flute - Solid Carbide Taper Tools
Usage: Soft Wood, Hard Wood, Soft Plastic, Hard Plastic, Aluminum
(SW) = Soft Wood
(HW) = Hard Wood
(SP) = Soft Plastics
(HP) = Hard Plastics
(A) = Aluminum
(CW) = Composite Wood
Onsrud Series 80-000

3 Flute – High Speed Steel Taper Pin Upcut Spiral
Usage: Aluminum and non-abrasive hard plastics
(A) = Aluminum
Onsrud Series 81-000

2 Flute - High Speed Steel Low Helix Upcut Spiral
Usage: Aluminum
(A) = Aluminum
Onsrud Series 81-100

2 Flute – Solid Carbide Extrusion Cutters Spiral Upcut
Usage: Extrusion and sheet aluminum
(A) = Aluminum
Onsrud Series 83-300

2 Flute – Solid Carbide Stainless Steel Spiral Upcut; ESG Coated
Usage: Extrusion and sheet aluminum
(A) = Aluminum
Onsrud Series 90-00

2 Flute - Solid Carbide T Slot Cutter
Usage: Natural wood and Wood composites
(HW) = Hard Wood
(SW) = Soft Wood
(CW) = Composite Wood
Onsrud Series 91-000

2 Flute - Carbide Tipped Spoilboard Surfacing Cutters
Usage: Composite Wood, Plastic, Aluminum
(HP) = Hard Plastic
(SP) = Soft Plastics
(A) = Aluminum
(CW) = Composite Wood
Onsrud Series 91-100

2 Flute - Carbide Inserts Spoilboard Surfacing Cutters
Usage: Composite Wood, Plastic, Aluminum
(HP) = Hard Plastic
(SP) = Soft Plastics
(A) = Aluminum
(CW) = Composite Wood
Onsrud Series 15-50 - Tin Coated

1 Flute - High Speed Steel CNC Dor-Bits
Usage: Metal Clad Doors, Fiberglass Doors
(D) = Metal Doors